Casio Printer KL 780 User Manual

E
KL-780  
User’s Guide  
 
Tape Cutter  
Never touch the tape cutter while a tape cut operation is being  
performed. Doing so can result in cuts and other personal injury.  
Avoid unstable areas  
Never place the unit on a wobbly table or a high shelf. Doing so can  
cause it to fall, resulting in personal injury.  
Water and other foreign matter  
Microwave oven containers  
Never allow coffee, juice, or other drinks, or flower vases to spill on the  
unit. Liquid spilled on the unit creates the danger of fire and electrical  
shock. Should liquid ever spill onto the unit, immediately turn off power.  
Request servicing from your original dealer.  
Never allow metal objects or combustible materials to get into the air  
vents of the unit. Doing so creates the danger of fire and electrical  
shock.  
Never affix labels to containers used for heating food in a microwave  
oven. The label material contains metal, which creates the risk of  
sparking and burn injury when heated in a microwave oven. Heating  
in a microwave oven can also cause deformation of the container to  
which the label is affixed.  
Location  
Caution  
Avoid leaving the unit in areas subjected to high humidity and large  
amounts of dust. Such conditions create the danger of fire and  
electrical shock.  
Avoid leaving the unit on a kitchen table, next to a humidifier, or in any  
other area where it might come into contact with oil vapors or steam.  
Such conditions create the danger of fire and electrical shock.  
Never place heavy objects on the unit. Doing so creates the danger  
of the unit falling, resulting in personal injury.  
AC Adaptor  
Do not leave the power cord near stoves or other sources of intense  
heat. Doing so can melt power cord insulation and create the danger  
of fire and electrical shock.  
When unplugging the power cord from the wall socket, grasp the plug.  
Never pull on the cord itself. Doing so can damage the power cord  
and create the danger of fire and electrical shock.  
Whenever leaving the unit unattended for long periods, be sure to  
unplug it from the wall socket.  
At least once a year, unplug the AC adaptor from the electrical outlet  
and clean the area around the prongs of the plug. Dust build up around  
the prongs creates the danger of fire.  
Whenever moving the unit, be sure to unplug it from the wall socket.  
Leaving the unit plugged in when it is being moved can result in damage  
to the power cord and create the danger of fire and electrical shock.  
Whenever cleaning the unit, be sure to unplug it from the wall socket.  
When you are through using the unit, use its power switch to turn it  
off and then unplug it from the wall socket.  
E-2  
 
Batteries  
Introduction  
Misuse of batteries can cause them to leak acid that can cause  
damage to nearby items and creates the possibility of personal injury.  
Congratulations on your selection of the CASIO KL-780 Label Printer. This CASIO  
Label Printer makes it possible for you to print adhesive labels for a wide variety  
of applications, such as: name tags, cassette tape labels, floppy disks, binders,  
and other applications.  
Be sure that the plus (+) and minus (–) sides of each battery are  
facing correctly.  
Never mix batteries of different types.  
You can produce attractive, original labels thanks to such features as:  
Never mix new batteries and dead batteries.  
Variable tape sizes (6mm, 9mm, 12mm, 18mm)  
Attractive sans-serif font  
Font effects (shading, underline, box)  
Character Styles (normal, outline, shadow, raised)  
Built-in symbols  
Remove the batteries if you do not plan to use KL-780 for a long time.  
Use only the battery type specified for this label printer in this manual.  
Text memory  
Bar code  
Mirror image printing  
Memory  
You can even use tapes with optionally available holders to create your own  
Always keep separate written copies of any information you store in  
the memory of this label printer. Data stored in memory can be  
unexpectedly lost due to malfunction, repair, dead battery, etc.  
stamps.  
All of this makes the CASIO Label Printer the perfect tool for just about all of  
your labeling needs!  
Loading and replacing batteries  
Do not touch the springs inside the battery compartment cover with  
your fingers while loading or replacing batteries. The springs have  
sharp areas and can cut your fingers.  
Important!  
Contact a nearby dealer whenever you require servicing.  
Note that the manufacturer shall not be held liable for any loss or  
claims by third parties which may arise out of the use of this product.  
Note that the manufacturer shall not be held liable for any damages  
incurred as a result of data loss caused by malfunctions, repairs, or  
interruption of power supply.  
It is up to the user to keep backup records of important data.  
Keep this manual on hand for future reference.  
E-3  
 
Part 5 Character Size, Text Effects and Character Styles ..... E-13  
Character Size .......................................................................................... E-13  
Using Auto Sizing (AUTO) ................................................................ E-15  
To specify character sizes (MANUAL) .............................................. E-15  
Text Effects ............................................................................................... E-15  
To specify a text effect ...................................................................... E-15  
Character Styles ....................................................................................... E-16  
To specify a character style .............................................................. E-16  
Contents  
Important Safety Precautions .................................................... E-1  
Part 1 Getting Acquainted .......................................................... E-5  
Important Precautions ................................................................................. E-5  
General Guide............................................................................................. E-5  
Label Printer Menus .................................................................................... E-6  
Part 6 Printing ........................................................................... E-16  
Printing a Tape .......................................................................................... E-16  
To print a tape ................................................................................... E-16  
Mirror Image Printing ................................................................................ E-17  
To turn mirror image printing on and off ............................................ E-17  
Print Density.............................................................................................. E-17  
To adjust the print density ................................................................. E-17  
Part 2 Getting Ready................................................................... E-6  
Power Supply .............................................................................................. E-6  
Replacing Batteries ..................................................................................... E-6  
To load the batteries ........................................................................... E-7  
AC Adaptor .................................................................................................. E-7  
To connect the AC adaptor ................................................................. E-7  
Turning Power On and Off .......................................................................... E-7  
Resetting the Memory ................................................................................. E-8  
To reset the memory ........................................................................... E-8  
Auto Power Off Function ............................................................................. E-8  
Display Contrast .......................................................................................... E-8  
Tape Cartridges .......................................................................................... E-8  
To load a tape cartridge ...................................................................... E-8  
Part 7 Bar Code ......................................................................... E-18  
Bar Code ................................................................................................... E-18  
Bar Code Tape .................................................................................. E-18  
To print a bar code ............................................................................ E-18  
Part 8 Stamp Printing ............................................................... E-19  
To print a stamp tape ........................................................................ E-19  
Part 3 Inputting Characters and Symbols................................. E-9  
Display Symbols and Indicators .................................................................. E-9  
Basic Alpha-Numeric Input ........................................................................ E-10  
To input alpha-numeric characters .................................................... E-10  
About the CODE key… ............................................................................. E-11  
Special Symbols ....................................................................................... E-11  
To input special symbols ................................................................... E-11  
Part 9 Memory ........................................................................... E-19  
To store data ..................................................................................... E-19  
To recall text from memory ............................................................... E-20  
Part 10 Reference...................................................................... E-20  
Cleaning the Printer Head and Roller ....................................................... E-20  
To clean the printer head and roller .................................................. E-20  
Initial Power On Settings........................................................................... E-21  
Initializing the Label Printer ....................................................................... E-21  
To initialize the Label Printer ............................................................. E-21  
Bar Code Specifications............................................................................ E-21  
Troubleshooting ........................................................................................ E-22  
Error Messages/Display Messages .......................................................... E-23  
Alpha Characters ...................................................................................... E-25  
Symbols .................................................................................................... E-25  
Specifications ............................................................................................ E-26  
Part 4 Deleting and Inserting Characters ............................... E-12  
Moving the Cursor..................................................................................... E-12  
To move the cursor ........................................................................... E-12  
Deleting Individual Characters .................................................................. E-12  
To delete characters using the BS key ............................................. E-12  
To delete characters using the DEL key ........................................... E-12  
Clearing the Display .................................................................................. E-12  
To clear the display ........................................................................... E-12  
Text Editing ............................................................................................... E-12  
To insert new characters ................................................................... E-12  
To change existing characters to different ones................................ E-12  
E-4  
 
General Guide  
Part 1 Getting Acquainted  
8
1
2
This part of the manual provides you with important information you need to  
know in order to use the Label Printer to its full potential. Be sure to read it  
carefully before using the Label Printer for the first time.  
6
5
Important Precautions  
Keep your Label Printer out of areas subject to temperature extremes, moisture  
and direct sunlight. The recommended temperature range is 10° to 35°C (50°  
to 95°F).  
3
7
4
Dont let coffee, juice or other liquids splash onto the Label Printer.  
Never let paper clips, pins or other foreign objects get into the tape outlet slot  
or printer of the Label Printer.  
9
Do not pile heavy objects on top of the Label Printer.  
Never try to take the Label Printer apart or attempt your own maintenance.  
Do not drop your Label Printer and avoid strong impact.  
Do not pull on the tape or try to force it back into the Label Printer.  
Do not use benzine, thinner, or other volatile chemicals to clean the exterior  
of the Label Printer. Use a soft, dry cloth or a cloth dampened in a weak  
solution of a mild, neutral detergent and water. Wring the cloth out until all  
excess moisture is removed.  
A dirty printer head can cause printing to become smudged. When this  
happens, clean off the printer head by wiping it with a cotton swab moistened  
with alcohol (page E-20).  
1 Power Key  
5 Tape outlet  
6 Tape cutter button  
7 Optional AC Adaptor connector  
8 Liquid crystal display (LCD)  
9 Battery compartment  
Use of the Label Printer next to a television or radio may interfere with reception.  
Turn power on and off.  
2 Function key  
3 Letter keys  
4 Contrast dial  
E-5  
 
Label Printer Menus  
Replacing Batteries  
Label Printer operation is designed to be as simple as possible, thanks to on-  
screen menus that you can use to select the settings you need. Each menu is  
described in detail in the sections that follow in this manual, but note the following  
general points when using them.  
A handy low battery power indicator lets you know when battery power is getting  
too low for proper operation. The message LOW BATTERYappears on the  
display if battery power is low when you perform any of the following operations.  
Turn power on  
Execute a print operation  
The item that is underlined in a menu is the one that is currently selected.  
Whenever the LOW BATTERYmessage appears, press SET to clear it from  
the display. You should still be able to perform some Label Printer operations,  
but some power intensive operations (like printing) may become impossible if  
battery power is too low. In any case, you should replace batteries as soon as  
possible or switch to the AC adaptor as soon as possible after the LOW  
BATTERYmessage appears.  
Currently  
selected item  
, . : ;  
‘ ’ “ ” „  
? ! ¿ ¡ ~ ( ) + –  
Use c, v, x and z to move the underlining left, right, up and down and  
change the selected item.  
Press SET to execute the underlined item, or ESC to exit the displayed menu  
(and return to the previous menu or screen) without selecting anything.  
When you press SET to execute a menu item, the Label Printer either moves  
on to the next menu, or it executes the selected function and returns to the  
text input screen that you started from.  
Important!  
All data stored in memory is deleted whenever batteries go dead and when you  
replace batteries. Be sure to keep written backup copies of all important data.  
Batteries can burst or leak and damage your unit if you do not use them  
correctly. Note the following important points.  
Be sure that the plus (+) and minus () sides of each battery are facing correctly.  
Never mix batteries of different types.  
Never leave dead batteries in the Label Printer.  
Remove the batteries if you do not plan to use the Label Printer for a long  
time.  
Replace the batteries in accordance with the battery life marked on the side  
of the battery.  
Part 2 Getting Ready  
This part of the manual tells you how to load batteries and the tape cartridge,  
and how to perform other basic setups for the Label Printer.  
Warning!  
Never use recharged batteries with the unit.  
Do not expose batteries to direct heat, do not short circuit them, and do not  
try to take them apart.  
Keep batteries out of the reach of small children. If swallowed, consult  
with a physician immediately.  
Important!  
Be sure to read this section before attempting to use the Label Printer.  
Power Supply  
The Label Printer can be powered by sixAA-size alkaline batteries or an optional  
AC adaptor (AD-A95100).  
Be sure to replace the batteries in accordance with the battery life printed on  
the side of the battery itself.  
E-6  
 
To load the batteries  
AC Adaptor  
Note the following important precautions when using an AC adaptor to power  
your Label Printer.  
Caution  
Use only a genuine CASIO AD-A95100 AC adaptor with the same voltage  
rating as the household current in your area. Using a wrong adaptor can  
damage your Label Printer.  
Be sure to turn the Label Printer off before you connect the adaptor. Do not  
turn power on until the adaptor is connected to the Label Printer and plugged  
into and AC outlet.  
Do not touch the springs inside the battery  
compartment cover with your fingers while  
loading or replacing batteries. The springs  
have sharp areas and can cut your fingers.  
1. Turn power off.  
Be sure to unplug the AC adaptor from the AC outlet whenever you are not  
using the Label Printer.  
If you are using the optional AC adaptor for power, you should also unplug it  
from the Label Printer.  
2. Turn over the Label Printer.  
Open the battery compartment cover as shown  
in the illustration.  
To connect the AC adaptor  
Connect the adaptor to the Label Printer as shown  
in the illustration. Plug the other end into a standard  
household AC outlet.  
3. Load batteries into the battery compartment.  
Be sure to use alkaline batteries.  
Make sure the positive (+) and negative (–) ends  
of the batteries are facing in the correct directions.  
Turning Power On and Off  
Press ON/OFF to turn power on and off.  
Important!  
If you are using the Label Printer for the first time, you should reset it first.  
4. Replace the battery compartment cover.  
E-7  
 
Resetting the Memory  
Tape Cartridges  
You should reset the memory of the Label Printer before using it for the first  
time, after you have not used it for a long time, or if nothing happens when you  
turn power on, even after you change the batteries.  
Use the procedures described below to load a tape cartridge into the Label Printer.  
Important!  
Never try to push the tape back into the cassette. Once tape is out of the  
cassette, there is no way to wind it back in. Trying to do so can cause  
operational problems with the Label Printer.  
The following are the tape widths that can be used with this printer: 6mm,  
9mm, 12mm, 18mm.  
Important!  
Resetting Label Printer memory clears its memory of all input data.  
To reset the memory  
1. Make sure that Label Printer power is off.  
2. While holding down the PRINT and ESC keys, press ON/OFF to turn power  
on.  
To load a tape cartridge  
1. Make sure that the Label Printer is turned off.  
2. Lift open the cover.  
This prompt confirms whether or not you want to initialize the Label Printer.  
I N I T I A L ?  
S E T E S C  
3. Release the PRINT, ESC, and ON/OFF keys.  
4. Press SET to initialize the Label Printer or ESC to abort the reset operation  
without initializing anything.  
3. Remove the stopper from a new tape cartridge  
and check to see that the tape is ready to use.  
See Initializing the Label Printeron page E-21 for information on the initial  
default settings of the Label Printer following the reset operation.  
Auto Power Off Function  
If you do not perform any key operation for about six minutes, the Label Printer  
automatically turns power off. To restore power, press ON/OFF.  
Make sure that the tape is under the tape guide and that it is not bent or  
twisted.  
Tape guide  
Display Contrast  
Rotate the dial on the side of the Label Printer to adjust display contrast.  
NO!  
OK!  
Make sure that the tape does not extend too far  
past the tape guide. If it does, cut off the end with  
a pair of scissors.  
E-8  
 
4. Use a pencil or some other thin object to take  
up slack in the ink ribbon as shown in the  
illustration. Note that the tape does not move at  
this time.  
Part 3 Inputting Characters and Symbols  
If the ink ribbon is slack when you load it into the  
Label Printer, it can break or cause some other  
problem.  
Be sure to turn the ink ribbon take up spool only  
in the direction indicated by the arrow (a).  
Turn the spool until the other spool (b) starts  
turning in the direction noted by the arrow. This  
indicates there is no slack in the ribbon.  
This part of the manual tells you how to input characters. To make things easier to  
understand, we call everything you input a character, regardless of whether it is  
actually a letter, number, or symbol. Explanations here all use the default settings  
that are in effect from the initial power-on screen.  
(a)  
For information on using other character styles, effects and sizes, see page E-13.  
Important!  
You can input up to 95 characters per label. Further input becomes impossible  
after you input the 95th character.  
(b)  
5. Slide the printer head release in the direction  
indicated by the arrow.  
If there is a cartridge already in the Label Printer,  
remove it by grasping the cartridge on both sides  
with your thumb and forefinger, and lift straight  
up.  
Display Symbols and Indicators  
Before getting into actual input, you should first become acquainted with the  
symbols and indicators used on the Label Printer display.  
Bar code indicator  
Function indicator  
Effect indicators  
C A S I O  
Style indicators  
6. Load the tape cartridge into the Label Printer,  
making sure that the tape and ink ribbon pass  
between the head and roller.  
7. Return the printer head release to its original  
position by sliding in the direction opposite to  
that indicated by the arrow in the illustration in  
step 5.  
Roller  
Shift  
indicator  
Stamp  
printing  
indicator  
Head  
C OM P U T E R • •  
Code  
indicator  
8. Close the cover.  
Cursor  
Character position marks  
Caps indicator  
9. Turn on Label Printer power and press FUNC and then PRINT (FEED) two  
or three times to make sure that the tape comes out without any problem.  
If the tape does not come out normally, turn off power and start again from  
step 1 above.  
Mirror image  
printing indicator  
Function indicator  
This indicator appears when you press the FUNC key. Pressing a key while this  
indicator is on the display causes the function marked above that key to be  
executed.  
Storage Precautions  
Keep tape cartridges out of areas subject to high temperature, humidity, and  
direct sunlight. These conditions can cause discoloration of the tape.  
When storing a cartridge, re-attach its stopper, and insert the cartridge in its  
original plastic bag and box.  
E-9  
 
Style indicators  
Shift indicator  
These indicators point to the character style that is currently in use. You can  
select between normal, outline, shadow, and raised.  
This indicator appears when you press the SHIFT key. While this indicator is on  
the display, the keyboard is shifted, so the letter keys input upper-case alpha  
characters. The number keys input the punctuation symbols marked in the upper  
right corners of the keys.  
Mirror image printing indicator  
This indicator appears when the Label Printer is set up for mirror image printing.  
Normal (non mirror image) printing is performed when this indicator is not shown.  
If both the caps mode indicator and the shift indicator are shown on the display,  
the keyboard is shifted to lower-case input.  
The keyboard automatically unshifts (and the shift indicator disappears) as soon  
as you input a character.  
Cursor  
The cursor shows the next input position. Any character you input appears at  
the point where the cursor is located.  
Code indicator  
This indicator appears when you press the CODE key. While this indicator is on  
the display, number keys 1 through 0 input the accents marked above them and  
the U, O, P, A, S, J, K, L, Z, C and N keys input the special characters marked  
in their lower right corners.  
Character position marks  
These marks show where characters will appear as you input them. This part of  
the display is always blank when you turn power on.  
The keyboard automatically returns to normal (and the code indicator disappears)  
as soon as you input an accent.  
Basic Alpha-Numeric Input  
The following operation shows you the basic procedures for inputting letters  
and numbers. We will explain the procedure by inputting the following characters  
using the default initial power-on screen.  
Caps indicator  
This indicator appears when the Label Printer is in the caps (upper-case) mode.  
All letters you input in the caps mode are upper-case. When the caps mode  
indicator is not shown on the display, all letters are input as lower-case.  
Note that the Label Printer stays in the caps mode until you press the CAPS  
key again.  
ABXYZ Computer Company  
1234567890  
Note  
If both the caps mode indicator and the shift indicator are shown on the display,  
the keyboard is shifted to lower-case input.  
If you hold down any key, it will repeat its operation or input at high speed until  
you release it.  
Bar code indicator  
This indicator appears when you are performing a bar code operation.  
To input alpha-numeric characters  
1. Turn power on.  
2. Input the first line of characters.  
Stamp printing indicator  
To input the upper-case letters, you can use either SHIFT or CAPS. With  
SHIFT you must shift the keyboard for each character. With CAPS the keyboard  
stays in upper-case until you press CAPS again.  
Press SPACE to input spaces.  
If you input a wrong character, press BS to delete it and input again. See  
page E-12 for other details on editing text.  
This indicator appears when you are performing a stamp operation.  
Effect indicators  
These indicators point to the character effect that is currently in use. You can  
select between shading, underline, and box.  
E-10  
 
I CAPS off  
3. When you reach the end of a line of text, press B to input a newline mark.  
A newline operation is indicated on the display by the B symbol. This shows  
where you changed lines.  
Key Operation  
Input  
Key Operation  
Input  
Key Operation  
Input  
CODE U  
CODE O  
CODE P  
CODE A  
CODE S  
CODE J  
CODE K  
ü
œ
å
æ
ß
CODE L  
CODE Z  
CODE C  
CODE N  
CODE 1  
CODE 2  
CODE 3  
j
w
ç
ñ
CODE 4  
CODE 5  
CODE 6  
CODE 7  
CODE 8  
CODE 9  
CODE 0  
The maximum number of lines you can input depends on the width of the  
˜
ˆ
ˇ
tape you have loaded in the Label Printer.  
Tape Width Maximum Number of Lines  
6mm ............................ 1  
°
/
´
`
¨
ö
ä
9mm ............................ 1  
˝
˛
12mm .......................... 2  
18mm .......................... 3  
Example: To input á.  
1. Press CODE.  
4. Input the characters in the second line.  
5. To print the text that you input, press PRINT. For details on printing, see  
page E-16.  
2. Press 1.  
3. Press A.  
About the CODE key…  
The CODE key makes it possible to input punctuation needed for a number of  
different languages. The following shows the key operations you should use for  
each of the characters formed using the CODE key.  
Special Symbols  
You can also access a menu of special symbols by pressing SYMBOL.  
I CAPS on  
To input special symbols  
Key Operation  
Input  
Key Operation  
Input  
Key Operation  
Input  
1. With the cursor at the location where you want to input a special symbol,  
press FUNC and then 7 (SYMBOL).  
The symbol that is underlined on the display is the one that is currently selected.  
CODE U  
CODE O  
CODE P  
CODE A  
CODE J  
CODE K  
CODE L  
Ü
Œ
Å
Æ
Ö
Ä
CODE Z  
CODE C  
CODE N  
CODE 1  
CODE 2  
CODE 3  
CODE 4  
W
Ç
Ñ
CODE 5  
CODE 6  
CODE 7  
CODE 8  
CODE 9  
CODE 0  
ˆ
ˇ
°
/
, . : ;  
‘ ’ “ ” „  
´
`
¨
˜
˝
˛
? ! ¿ ¡ ~ ( ) + –  
J
2. Use the c, v, x and zcursor keys to move the underlining to the symbol  
you want.  
Not all of the available symbols fit on the display. The menu will scroll when  
you press the cursor keys.  
3. After you underline the symbol you want, press SET.  
This returns to the input screen, with the symbol you selected input at the  
location where the cursor was located when you displayed the symbol list.  
E-11  
 
To delete characters using the DEL key  
Part 4 Deleting and Inserting Characters  
Example: To change the word commmputerto computer.  
1. Use cand vto move the cursor under the first (far left) m.  
2. Press DEL twice to delete the two ms at the cursors position, shifting mputer”  
to the left as you do.  
This section describes everything you need to know about deleting and editing  
characters you have already input.  
3. Press FUNC and then vto jump back to the end of the characters for more  
input.  
Moving the Cursor  
Use the cursor keys to move the cursor around the display and position it for  
deleting and editing characters.  
Clearing the Display  
Use the following procedure to clear all input text from the display.  
To move the cursor  
Press cto move the cursor to the left, and vto move the cursor to the right.  
Press FUNC and then cto make the cursor jump to the beginning (far left) of  
the characters on the display.  
To clear the display  
Press FUNC and then DEL (CLS).  
At this time the message CLS OK? SET/ESCappears on the display to confirm  
that you want to clear the display. Press SET to clear or ESC to abort the operation  
without clearing anything.  
Press FUNC and then vto make the cursor jump to the end (far right) of the  
characters on the display.  
Holding down the cor vcursor key moves the cursor at high speed.  
Text Editing  
Deleting Individual Characters  
You can delete individual characters with either the BS key or the DEL key. The  
only difference between the operation of these two keys is the location of the  
cursor.  
You can use the following procedures to edit text on the display.  
To insert new characters  
Example: To change the text ABCDEFto ABCXYZDEF.  
To delete characters using the BS key  
Example: To change the word CASSSIOto CASIO.  
1. Use cand vto move the cursor under I.  
1. With the original text on the display, move the cursor under the letter D.  
2. Input the new characters (XYZ).  
Inputting the new characters causes them to be inserted at the cursor position.  
The existing characters are opened up to make room for the new characters.  
To change existing characters to different ones  
C A S S S I O  
Example: To change the text ABCDEFto XYZDEF.  
1. With the original text on the display, use either the BS key or DEL key to  
delete the characters to be changed (ABC).  
2. Input the new characters (XYZ).  
2. Press BS twice to delete the two Ss to the left of the cursor, shifting IOto  
the left as you do.  
3. Press FUNC and then vto jump back to the end of the characters for more  
input.  
E-12  
 
Actual Size  
(Vertical × Horizontal mm)  
6mm × 3mm  
Character Size Indicator  
Part 5 Character Size, Text Effects and Character Styles  
2 × 1  
2 × 2  
2 × 3  
2 × 4  
2 × 5  
2 × 6  
3 × 1  
3 × 2  
3 × 3  
3 × 4  
3 × 5  
3 × 6  
4 × 1  
4 × 2  
4 × 3  
4 × 4  
4 × 5  
4 × 6  
6mm × 6mm  
6mm × 9mm  
6mm × 12mm  
6mm × 15mm  
6mm × 18mm  
9mm × 3mm  
This part of the manual explains how to set the size of characters.  
It also tells you how to assign text effects like underlining, shading, and box  
printing, and how to select character styles like normal, outline, shadow, and  
raised.  
Character Size  
9mm × 6mm  
9mm × 9mm  
There are two methods you can use to set the character size: AUTO and  
MANUAL. With AUTO, character size is set automatically in accordance with  
the tape size you are using and the number of lines you are printing. MANUAL  
lets you set the character size manually.  
9mm × 12mm  
9mm × 15mm  
9mm × 18mm  
12mm × 3mm  
12mm × 6mm  
12mm × 9mm  
12mm × 12mm  
12mm × 15mm  
12mm × 18mm  
The following table shows how AUTO decides which character size to use.  
Number of lines/tape size  
tape size  
6mm  
9mm  
12mm  
18mm  
number of lines  
1 line  
1 × 1  
2 × 2  
3 × 3  
1 × 1  
3 × 3  
1 × 1  
1 × 1  
2 lines  
3 lines  
Character size changes are applied to printed text only. The size of the displayed  
text does not change.  
The following table shows the 24 characters sizes that are available with  
MANUAL size setting.  
Important!  
Any character size specification you make is applied to all the characters on  
the display. You cannot make multiple specifications for specific characters.  
The maximum character size you can print depends on the size of the tape  
you have loaded in the Label Printer and the number of lines of text you are  
printing. If the character size you specify is greater than the maximum  
characters size limit, the Label Printer automatically adjust your text vertically  
to fit as shown in the tables below. The indicator Eis shown on the right of  
the size to indicate when the character size has been adjusted.  
Actual Size  
Character Size Indicator  
(Vertical × Horizontal)  
1 × 1  
1 × 2  
1 × 3  
1 × 4  
1 × 5  
1 × 6  
3mm × 3mm  
3mm × 6mm  
3mm × 9mm  
3mm × 12mm  
3mm × 15mm  
3mm × 18mm  
E-13  
 
6mm (1 line)  
12mm (2 lines)  
Horizontal  
3
Horizontal  
3
1
2
4
5
6
1
2
4
5
6
1
2
3
4
1 × 1  
1 × 1  
1 × 1  
1 × 1  
1 × 2  
1 × 2  
1 × 2  
1 × 2  
1 × 3  
1 × 3  
1 × 3  
1 × 3  
1 × 4  
1 × 4  
1 × 4  
1 × 4  
1 × 5  
1 × 5  
1 × 5  
1 × 5  
1 × 6  
1 × 6  
1 × 6  
1 × 6  
1
2
3
4
1 × 1  
1 × 1  
1 × 1  
1 × 1  
1 × 2  
1 × 2  
1 × 2  
1 × 2  
1 × 3  
1 × 3  
1 × 3  
1 × 3  
1 × 4  
1 × 4  
1 × 4  
1 × 4  
1 × 5  
1 × 5  
1 × 5  
1 × 5  
1 × 6  
1 × 6  
1 × 6  
1 × 6  
9mm (1 line)  
18mm (1 line)  
Horizontal  
3
Horizontal  
3
1
2
4
5
6
1
2
4
5
6
1
2
3
1 × 1  
2 × 1  
3 × 1  
4 × 1  
1 × 2  
2 × 2  
3 × 2  
4 × 2  
1 × 3  
2 × 3  
3 × 3  
4 × 3  
1 × 4  
2 × 4  
3 × 4  
4 × 4  
1 × 5  
2 × 5  
3 × 5  
4 × 5  
1 × 6  
2 × 6  
3 × 6  
4 × 6  
1
2
3
4
1 × 1  
2 × 1  
2 × 1  
2 × 1  
1 × 2  
2 × 2  
2 × 2  
2 × 2  
1 × 3  
2 × 3  
2 × 3  
2 × 3  
1 × 4  
2 × 4  
2 × 4  
2 × 4  
1 × 5  
2 × 5  
2 × 5  
2 × 5  
1 × 6  
2 × 6  
2 × 6  
2 × 6  
4
*
12mm (1 line)  
At this size, certain text effects can cause closely spaced lines of text to overlap.  
When this size is being used, you cannot change the character style (page  
E-16).  
*
*
Horizontal  
3
1
2
4
5
6
18mm (2 lines, 3 lines)  
1
2
3
4
1 × 1  
2 × 1  
3 × 1  
3 × 1  
1 × 2  
2 × 2  
3 × 2  
3 × 2  
1 × 3  
2 × 3  
3 × 3  
3 × 3  
1 × 4  
2 × 4  
3 × 4  
3 × 4  
1 × 5  
2 × 5  
3 × 5  
3 × 5  
1 × 6  
2 × 6  
3 × 6  
3 × 6  
Horizontal  
3
1
2
4
5
6
1
2
3
4
1 × 1  
1 × 1  
1 × 1  
1 × 1  
1 × 2  
1 × 2  
1 × 2  
1 × 2  
1 × 3  
1 × 3  
1 × 3  
1 × 3  
1 × 4  
1 × 4  
1 × 4  
1 × 4  
1 × 5  
1 × 5  
1 × 5  
1 × 5  
1 × 6  
1 × 6  
1 × 6  
1 × 6  
Important!  
Whenever a horizontal size of 1 is being used, the lines of certain character  
styles can become broken.  
E-14  
 
Using Auto Sizing (AUTO)  
1. Input the text.  
2. Press FUNC 4 (SIZE) to display the size setting menu.  
Text Effects  
There are three text effects that you can assign: shading, underlining, and boxed  
text. The following shows examples of each.  
A U T O  
Shading:  
M A N U A L  
Underlining:  
Boxed Text:  
3. Make sure the pointer is aligned with AUTO and then press SET.  
Now the character size is automatically set.  
To specify character sizes (MANUAL)  
1. Input the text.  
2. Press FUNC 4 (SIZE) to display the size setting menu.  
3. Use zto move the pointer to MANUAL and then press SET.  
Text effect changes are applied to printed text only. The appearance of the  
displayed text does not change, but the text effect indicators will show you when  
a text effect is being used.  
Important!  
Any text effect specification you make is applied to all the characters on the  
display. You cannot make multiple specifications for specific characters.  
You can use the Shading, Underline, and Box effects in combination with  
each other, and even specify all three at the same time.  
M A N U A L  
S I Z E :  
3
3
4. Specify the character size you want.  
To specify a text effect  
Use cand vto move the underlining between the two dimensions.  
To change a dimension, press zto increase it or xto decrease it.  
Remember that the dimensions you can specify depend on the width of the  
tape loaded in the label printer (see table, above).  
1. Input the text.  
2. Press FUNC 5 (EFFECT) to display a menu of text effects.  
C A N C E L  
S H A D I N G  
5. When the character size you want to specify is on the display, press SET to  
select it and return to the text display.  
Note  
You could also perform the above procedure in reverse, specifying the  
character size first and then inputting the text.  
3. Use zand xto move the pointer to the effect you want to use.  
4. When the pointer is located at the effect you want to specify, press SET to  
select it and return to the text display.  
Note  
You could also perform the above procedure in reverse, specifying the text  
effect first and then inputting the text.  
E-15  
 
Character Styles  
There are four character styles that you can assign; normal, outline, shadow,  
and raised. The following shows examples of each.  
Part 6 Printing  
Style  
Normal  
Outline  
Shadow  
Raised  
Indicator  
Sample  
This part of the manual includes all the information you need to print tapes. It  
also tells you how to print special stamp tapes that you can attach to an optional  
stamp holder to create your own original stamps.  
None  
Printing Precautions  
Never turn power off while printing is being performed.  
Make sure that the tape outlet is not blocked before you start printing.  
Never operate the tape cutter while printer is being performed (indicated by  
the message NOW PRINTINGon the display).  
Character style changes are applied to printed text only. The appearance of the  
displayed text does not change, but the character style indicators will show you  
when a character style is being used.  
Important!  
Never touch the tape cutter while a tape cut operation is being performed.  
Important!  
Doing so can result in cuts and other personal injury.  
Any character style specification you make is applied to all the characters on  
the display. You cannot make multiple specifications for specific characters.  
Only one character style can be in effect at a time. You cannot combine  
character styles.  
Printing a Tape  
Printing a tape is as easy as pressing the PRINT key.  
To specify a character style  
To print a tape  
1. Press the PRINT key to print a tape of the text you have input and laid out.  
To stop a print operation that is in progress, press ESC.  
1. Input the text.  
2. Press FUNC 6 (STYLE) to display a menu of character styles.  
2. After the print operation is complete, press down on the tape cutter button to  
cut the tape.  
3. Use scissors to trim the tape to the size you want, if necessary.  
After you print a tape, you can peel off its paper  
backing and stick the tape onto the object you  
N O R M A L  
O U T L I N E  
3. Use zand xto move the pointer to the style you want to use.  
4. When the pointer is located at the style you want to specify, press SET to  
select it and return to the text display.  
want. Note that the tape will not stick on coarse,  
wet, oily, or soiled surfaces. Also, you should not  
try to use the tape where it is exposed to direct  
sunlight or rain. Do not stick the tape onto human  
skin.  
Backing  
Note  
Tape  
You could also perform the above procedure in reverse, specifying the  
character style first and then inputting the text.  
E-16  
 
An easy way to remove the backing from a tape  
and expose the adhesive surface is to bend the  
tape near one of its ends. This should cause the  
tape and its backing to separate, allowing you to  
pull them apart.  
Print Density  
The print density setting controls how darkly figures are printed on your tapes.  
To adjust the print density  
1. Press FUNC and then 9 (DENSITY).  
D E N S I T Y –  
Mirror Image Printing  
When you specify mirror image for text, it is printed in reverse image. Use mirror  
image when you plan to print on transparent tape, with the printing on the inside.  
When viewed through the transparent tape, the text will appear normal. You  
can also use mirror image printing when using iron-on transfer tape to print iron-  
on transfers.  
1
2
3
4
5
2. Use cand vto move the underlining to the density setting that you want.  
The lightest setting is 1, while the darkest setting is 5. The standard setting is 3.  
3. When the density setting is the way you want it, press SET to register it.  
Normal  
Mirror Image  
To turn mirror image printing on and off  
1. Press FUNC and then 8 (MIRROR).  
N O R M A L  
M I R R O R  
2. Press zor xto change the setting shown on the display between MIRROR  
and NORMAL.  
3. When the mirror image printing setting is the way you want it, press SET to  
register it.  
A mark appears next to the MIRROR indicator on the display when mirror  
printing is turned on.  
After you turn printing on, input text and perform the print operation as you  
normally do to produce mirror image tapes.  
E-17  
 
2. Use zand xto move the pointer to the type of bar code you want to print  
and then press SET.  
Part 7 Bar Code  
Bar Code  
(ex. EAN-13)  
With this item, you can print two different types of bar codes: EAN-13, EAN-8.  
3. Input 12 number of digits when you are using EAN-13 (7 digits, when using  
Important!  
EAN-8), and then press SET.  
The procedure you use to print a bar code depends on the type of bar code  
you select.  
4. Use cand vto move the underlining to the size you want to use and then  
press SET.  
S: SMALL  
M: MEDIUM  
L: LARGE  
Bar Code Tape  
Only the following types of tape should be used for printing bar codes.  
Black on white tape (WE)  
Blue on white tape (WEB)  
Black on yellow tape (YW)  
*
8
P R I N T ?  
S E T E S C  
Important!  
You cannot use 6mm or 9mm tapes to print bar codes.  
With bar codes, you can only input numeric characters (0 to 9). EAN-8 allows  
input of seven digits, while EAN-13 allows input of 12 digits.  
Always test bar codes produced using this label printer before actually using  
them. If bar codes cannot be read properly, try adjusting the print density or  
using a larger character size.  
* This number indicates the check digit. The check digit is automatically  
calculated in accordance with input data. For information on Bar Code  
Specifications, see page E-21.  
5. A prompt appears to confirm whether or not you want to perform printing.  
Press SET to execute it, or ESC to abort the operation.  
An error message TAPE ERROR USE 12, 18mmappears when you press  
SET while loading a 6mm/9mm tape. If this happens, reload a 12mm/18mm  
tape and try again. (See page E-8 for details on loading tape cartridges.)  
Do not use consecutive printing for bar codes.Consecutive printing can result  
in bar codes that cannot be read by a bar code reader.  
To print a bar code  
1. Press FUNC 1 (BAR CODE).  
E A N 1 3  
E A N 8  
E-18  
 
Part 8 Stamp Printing  
Part 9 Memory  
The stamp printing feature lets you print on special stamp tape. You can then  
attach the finished stamp tape to an optionally available stamp holder to create  
your own original pre-inked stamps. The following is the type of stamp holder  
currently available for use with stamp tapes.  
This part of the manual tells you how to store text data in memory for instant  
recall when you need it. You can store one block of text in memory, containing  
up of 95 characters.  
Important!  
Type Maximum Stamp Size  
ST-15 5.5cm  
Example  
All data stored in memory is deleted whenever batteries go dead and when  
you replace batteries. Be sure to keep written backup copies of all important  
data.  
10mm 18mm  
When using the optional AC adaptor, never disconnect the adaptor while  
batteries are not loaded in the Label Printer or when batteries are dead. Doing  
so causes all data stored in memory to be deleted.  
5.5cm  
9.3cm  
Note the following important points about stamp printing.  
Stamp printing prints text in mirror image.  
You can perform stamp printing only when 18mm is specified as the tape width.  
An error message LENGTH ERROR!appears on the display and the Label  
Printer refuses to print whenever you try to print text that is longer than the  
maximum length you specify.  
To store data  
1. Input the text you want to store.  
2. Press FUNC 3 (MEMO).  
3. Press zand xto select STORE.  
S T O R E  
R E C A L L  
To print a stamp tape  
1. Input the text you want to print.  
2. Press FUNC and then 2 (STAMP).  
4. Press SET to store the text in memory or ESC to abort the store procedure  
without storing anything.  
P R I N T ?  
C OM P L E T E  
S E T E S C  
3. Press SET to print the stamp tape or ESC to abort the print operation and  
return to the text input display in step 1.  
After the printing is complete, the Label Printer returns to the input display in  
step 1.  
If there is nothing in memory yet, pressing SET stores your text.  
If there is already text stored in memory, the message OVERWRITE? SET/  
ESCappears when you press SET. Press SET again to replace the existing  
text with the new text, or ESC to cancel the store operation.  
4. Cut off the tape and affix it to the optional stamp holder.  
See the instructions that come with the optional stamp holder for information  
about how to attach the stamp tape.  
E-19  
 
To recall text from memory  
1. While the input screen is on the display, press FUNC 3 (MEMO).  
Note that text recalled from memory will replace any text currently on the  
display.  
Part 10 Reference  
This section contains information about the Label Printer that you can use as  
reference when you need it.  
2. Press zand xto select RECALL.  
S T O R E  
R E C A L L  
Cleaning the Printer Head and Roller  
A dirty printer head and roller can result in poor printing quality. If you have  
problems with print quality, use the following procedure to clean the printer head  
and roller.  
3. Press SET.  
If all of the text does not fit on the display, you can use c, v, xand zto  
scroll it to the left, right, up and down.  
To clean the printer head and roller  
1. Make sure the Label Printer is turned off.  
2. Lift open the cover.  
3. Slide the printer head release in the direction  
indicated by the arrow, and remove the tape  
cartridge.  
4. Press SET to recall the text from memory.  
Note that recalling data from memory replaces anything that is currently on  
the input display. Memory text cannot be appended.  
4. Use a cotton swab dipped in alcohol to clean  
the printer head and roller as shown in the  
illustration.  
Printer head  
Roller  
5. Replace the tape cartridge and close the cover.  
E-20  
 
The following table shows the initial settings.  
Initial Power On Settings  
The following are the initial settings of the Label Printer whenever you turn it  
power on.  
Item  
Display  
Reset  
Cleared  
Cleared  
Item  
Power On  
6mm tape...1 × 1  
9mm tape...2 × 2  
12mm, 18mm tapes...3 × 3  
CANCEL  
Memory  
SYMBOL  
SIZE  
EFFECT  
STYLE  
MIRROR  
MEMO  
DENSITY  
,
SIZE  
AUTO SIZE  
AUTO  
CANCEL  
NORMAL  
NORMAL  
STORE  
3
EFFECT  
STYLE  
MIRROR  
NORMAL  
NORMAL  
Initializing the Label Printer  
Bar Code initial setting  
If you experience serious malfunction of the Label Printer or if operation fails  
completely, try performing the following operation to initialize the printer.  
Item  
Menu  
Reset  
EAN-13  
Cleared  
Important!  
Initializing the Label Printer deletes all memory contents. Make sure you have  
a back-up copy of text stored in memory if you need it.  
Text  
Size  
M (MEDIUM)  
To initialize the Label Printer  
1. Turn power off.  
Bar Code Specifications  
2. While holding down the PRINT and ESC keys, press ON/OFF to turn power on.  
This prompt confirms whether or not you want to initialize the Label Printer.  
Automatically  
Assigned  
Bar code  
Type  
Check  
Print  
Input  
Input  
Digit *1 Digit *2 Digits *3  
Number of Digits  
(Check Digit *1)  
Characters  
I N I T I A L ?  
S E T E S C  
EAN-13  
EAN-8  
Yes  
Yes  
13  
8
12  
7
1
1
Numerals (0 ~ 9)  
Numerals (0 ~ 9)  
3. Release the PRINT, ESC, and ON/OFF keys.  
4. Press SET to initialize the Label Printer or ESC to abort the reset operation.  
*1 The check digit is automatically calculated in accordance with input data.  
For EAN-13 and EAN-8, the check digit is appended at the end of the printed  
digits.  
*2 The number of digits printed below a bar code equals the input characters  
plus automatically appended characters.  
*3 An error message is displayed whenever there are insufficient digits. The  
unit will not allow input of too many digits.  
E-21  
 
Printing  
Troubleshooting  
Tape does not come out when PRINT is pressed.  
Power Supply  
Possible Causes  
Action  
Page  
Nothing appears on the display.  
Possible Causes Action  
Low batteries Replace batteries.  
Tape cartridge  
compartment cover is not  
closed completely.  
Securely close the cover.  
Page  
E-8  
E-6  
Improper display contrast  
setting  
Adjust display contrast.  
No more tape left in the  
cartridge.  
Replace the tape cartridge with a  
new one.  
E-8  
E-7  
E-7  
E-8  
E-8  
Batteries loaded  
incorrectly  
Remove batteries and reload them  
correctly.  
Tape jam  
Remove the tape cartridge and pull  
out the jammed tape by hand. Cut off  
excess tape with scissors, and  
carefully replace the cartridge into  
the label printer.  
AC adaptor is not  
connected correctly.  
Make sure the AC adaptor is  
connected correctly.  
Important!  
Never allow the tape outlet to  
become blocked and never touch  
tape as it is being fed during printing.  
Text Input  
Cannot input text.  
Action  
Tape comes out when PRINT is pressed, but nothing is printed on it.  
Possible Causes  
Page  
Possible Causes  
Action  
Page  
FUNC key has been  
pressed.  
Press ESC to clear FUNC key  
operation.  
E-9  
Only blank spaces were  
input.  
Input the text you want to print.  
E-9  
Printing is blurred, blotched, broken, etc.  
Possible Causes  
Action  
Page  
Improper print density  
setting  
Adjust the print density setting.  
E-17  
Improper loading of the  
cartridge  
Remove the tape cartridge and  
reload it correctly.  
E-8  
Dirty printer head or  
rubber roller  
Clean the printer head and roller.  
E-20  
E-22  
 
Using Labels  
Ink ribbon is being fed from the tape outlet along with the tape.  
Label will not adhere to a surface.  
Possible Causes  
Action  
Page  
Possible Causes  
Action  
Page  
Tape cartridge loaded  
while the ink ribbon is  
slack.  
Remove the tape cartridge and check  
to make sure the ink ribbon is not  
broken. Next, take up any slack in the  
ink ribbon and then reload the tape  
cartridge.  
The backing paper is still  
on the back of the tape.  
Peel the backing paper from the back  
of the tape to expose the adhesive.  
E-16  
Surface is unsuitable for  
affixing a tape.  
Labels do not adhere well to surfaces  
that are rough, wet, oily, or dirty.  
E-16  
Important!  
E-8  
Before loading a tape cartridge into  
the label printer, always make sure  
you take up any slack in the ink  
ribbon first.  
If the ink ribbon is broken, you  
must change to another tape  
cartridge.  
Error Messages/Display Messages  
Message  
Possible Causes  
Action  
The number carriage  
returns you input causes  
the label to exceed the  
maximum number of lines  
for the tape you are  
using.  
Use wider tape or reduce  
the number of lines.  
6mm tape...1 line  
¥
ERROR!  
*This message  
appears on the  
screen for about  
one second.  
9mm tape...1 line  
Tape Cutting  
12mm tape...Up to 2 lines  
18mm tape...Up to 3 lines  
Reduce the number of  
lines of text to two.  
Cannot cut tape.  
Action  
You are attempting to  
print a stamp while three  
lines of text are input.  
Possible Causes  
Page  
Tape cutter blade is dull.  
Take the label printer to the dealer  
from whom you purchased it to have  
the tape cutter blade replaced.  
You are attempting to  
recall text from memory  
when there is none  
stored.  
NO DATA!  
*This message  
appears on the  
screen for about  
one second.  
Printed text is cut off by tape cut operation.  
Possible Causes  
Out of tape  
Action  
Page  
Replace the tape cartridge with a new  
one.  
E-8  
OVERWRITE?  
SET/ESC  
You are attempting to  
store text in memory  
when it already containes  
text.  
Press SET to overwrite  
the existing text with the  
new text, or ESC to  
cancel the store  
operation.  
E-23  
 
Message  
Possible Causes  
Action  
Message  
Possible Causes  
Action  
INPUT TEXT!  
Attempt to store text data, Input the text you want  
TAPE ERROR  
Press any key besides  
ON/OFF to clear the error  
message.  
Turn the power OFF and  
set the tape cartridge.  
when no text are input.  
You are attempting to  
print a stamp without  
inputting text.  
to store and try again.  
Input the text you want  
to print and try again.  
* This message  
appears on the  
screen for about  
one second.  
You are attempting to  
perform printing without  
setting a tape cartridge.  
You are attempting to  
print a stamp using a tape  
size other than 18mm.  
You are attempting to  
perform a bar code  
Use only 18mm tape to  
print a stamp.  
Use only 12 or 18mm  
tapes to perform bar  
code operation.  
operation using a 6mm or  
9mm tape.  
LENGTH  
ERROR!  
You are attempting to  
print a stamp with text  
that is longer than 5.5cm.  
Shorten the text you are  
printing and try again.  
* This message  
appears on the  
screen for about  
one second.  
LOW BATTERY  
DATA ERROR!  
Battery power is low.  
Replace the batteries.  
Data in memory has  
become corrupted for  
some reason.  
Press any key besides  
ON/OFF to clear the  
error message. In  
response to the  
INITIAL?message that  
appears, press SET to  
initialize the Label  
Printer.  
DIGIT ERROR!  
Input of the wrong number Input the correct number  
of digits for a bar code  
operation.  
of digits for the type of bar  
code you are creating.  
EAN-8 ... 7 digits  
* This message  
appears on the  
screen for about  
one second.  
EAN-13 ... 12 digits  
E-24  
 
Alpha Characters  
Symbols  
E-25  
 
General  
Specifications  
Power supply: Six AA-size alkaline batteries or optional AD-A95100 AC adaptor  
Battery life: Approximately 4 tape cartridges (continuous printing)  
Power consumption: 9W  
Auto Power Off: Approximately six minutes after last key operation.  
Dimensions: 51.5 (H) × 180 (W) × 217 (D)mm  
Weight: Approximately 470g  
Model: KL-780  
Input  
Keyboard Layout: Typewriter (QWERTY)  
Ambient Temperature: 10°C~35°C (50°F~95°F)  
Character Types  
Alpha (English and other languages): 151  
Numbers: 10  
Symbols: 46  
Display  
Type: Liquid crystal display  
Character matrix: 10 columns × 2 lines of 5 × 7-dot  
Printing  
Type: Thermal transfer  
Speed: Approximately 6.58mm/second  
Width: 4mm (6mm tape), 7mm (9mm tape), 10mm (12mm tape), 12mm (18mm  
tape)  
Character Matrix: 48 × 48-dot  
Character font: Sans-serif  
Character effects: Shade, underline, box  
Character Styles: Normal, Outline, Shadow, Raised  
Character sizes: 1 × 1, 1 × 2, 1 × 3, 1 × 4, 1 × 5, 1 × 6, 2 × 1, 2 × 2, 2 × 3, 2 × 4,  
2 × 5, 2 × 6, 3 × 1, 3 × 2, 3 × 3, 3 × 4, 3 × 5, 3 × 6, 4 × 1, 4 × 2,  
4 × 3, 4 × 4, 4 × 5, 4 × 6  
Number of lines: 1 (6mm and 9mm tapes); 1 or 2 (12mm tape); 1 or 2 or 3  
(18mm tape)  
Memory  
Text: Up to 95 characters  
E-26  
 
CASIO COMPUTER CO., LTD.  
6-2, Hon-machi 1-chome  
Shibuya-ku, Tokyo 151-8543, Japan  
MO0306-B  
 

Black Decker Can Opener EC75 User Manual
Black Decker Vacuum Cleaner VS1300 User Manual
Blaupunkt Network Card 7607545500 User Manual
BOXLIGHT Projector CD 450m User Manual
Bravetti Food Processor FP107H User Manual
Briggs Stratton Plumbing Product 073001 User Manual
Brother Printer 2420PC User Manual
Brother Sewing Machine CS 80 User Manual
Canon Camera Lens 11 24mm f 4L User Manual
Christie Digital Systems Projector DS+300 User Manual