Cateye Bicycle Accessories CC MC100W User Manual

ENG  
®
11  
MICRO Wireless  
CYCLOCOMPUTER  
CC - MC100W  
Owner’s Manual  
Max.  
Distance  
U.S. Pat. Nos. 4633216/4636769/4642606/5236759 and Design Pat. Pending  
Copyright© 2004 CAT EYE Co., Ltd.  
CCMC1W-041129 066600370 2  
70 cm  
1
2
4
5
Component name  
1 Bracket  
2 Speed Sensor A  
3 Magnet  
4 Bracket Rubber Pad  
5 Sensor Rubber Pad  
6 Nylon Ties (L x2)  
7 Nylon Ties (S x2)  
8 Double-sided tape  
33  
22  
6
7
3
8
1
8
1
8
1
7
or  
1
4
1
7
5
2
2
3
3
6
2
SENSOR ZONE  
A
2
B
5 mm  
SENSOR  
ZONE  
3
2
3
1
 
Troubleshooting  
No display.  
Is battery in the computer run down?  
Replace it, and re-enter the correct information. (All Clear ).  
CAUTION  
Standard Parts  
• Do not concentrate on the computer while riding. Be sure to  
ride safely!  
ENG  
• Install the magnet, sensor, and bracket securely. Check these  
periodically.  
a
#169-6590  
Incorrect data appears.  
Parts Kit  
• Dispose of used batteries according to local regulations. If swal-  
lowed, consult a doctor immediately.  
Do all clear operation. (All Clear  
Pressing the START/STOP button does not calculate Elapsed Time.  
Is the icon illuminated?  
To start/stop measurement using the START/STOP button, turn off  
Auto-mode.  
The sensor signal icon does not flash. (The speed is not displayed.)  
[If the signal icon does not flash, reduce the distance between the sensor  
and computer, adjust the position of the magnet, and spin the wheel again.  
If the icon now flashes, this indicates that the computer and sensor are  
too far apart or that the battery is low.]  
Is the clearance between the sensor and magnet too great?  
Does the magnet pass through the sensor zone?  
Adjust the positions of the magnet and sensor.  
a
).  
• Avoid having the computer in hot direct sunlight for extended  
periods.  
• Do not disassemble the computer.  
• Clean the computer and accessories with a soft cloth damp-  
ened with a neutral detergent. Do not use thinners, benzene, or  
alcohol on the computer.  
#169-6580  
Wireless Sensor  
Speed Sensor A  
The sensor was designed to receive signals within a limited range to  
prevent sensor signal interference. Thus, the sensor and computer  
must be relatively close. If the temperature or battery power is low,  
they may need to be even closer than normal. The sensor must be  
installed at the top of the fork, and the distance between the sensor  
and the computer should not exceed approximately 70 cm. Install  
the computer on the stem, with its bottom surface facing the sensor.  
(Take into account the angle of the stem.)  
Is the computer installed at the correct angle?  
Install the computer with its bottom surface facing the sensor.  
#169-6570  
Is the distance between the computer and sensor too great?  
Install the sensor closer to the computer.  
Is the sensor battery weak?  
In winter, battery performance degrades.  
Replace it.  
Bracket kit  
Interference may occur, resulting in malfunction, if the computer is:  
• Near a TV, PC, radio, motor, or in a car or train.  
• Close to a railroad crossing, railway tracks, TV stations and or  
radar base.  
Is the computers battery weak?  
Replace it with a new one. (All Clear  
• Close to a second bicycle with wireless sensors.  
#169-9691  
a
).  
Correct installation of sensor and magnet  
Attach the magnet 3 so that it passes through the sensor  
zone of the sensor 2.  
Be sure to have a 5 mm-or-less clearance between the sensor  
2 and magnet 3.  
Part names  
Current Speed  
Sensor signal reception icon  
Flashes in sync with sensor signals.  
Sub measurement icon  
Wheel Magnet  
Replacing the Battery  
• Computer  
If the Wheel Size icon (  
A
B
or  
) flashes, replace the battery.  
The Total Distance can be entered manually. Before removing  
the battery, note the current Total Distance. Install a new lithium  
battery (CR2032) with the (+) side facing upward.  
Then re-start the computer according to the SETTING proce-  
dure, and then set the clock from the MENU FLOW.  
• Sensor  
#166-5150  
Lithium Battery (CR2032)  
A
B
C
D
If sensor reception is poor, replace the battery. Then check the  
positions of the battery and magnet.  
Pace arrow  
Option Parts  
Indicates whether the current speed is faster or slower than  
the average speed. ( Faster Slower)  
Auto mode icon  
Specification  
Battery ............. Computer: Lithium Battery CR2032 X 1  
Sensor: Lithium Battery CR2032 X 1  
E
F
#169-6667  
Battery Life ...... Computer: approx. 1 year (If the computer is used for  
1 hour/day without the backlight on)  
Speed unit  
Center Mount Kit  
b
G
Mode symbol ....................................................................  
Sensor: until Total Distance reaches about 10,000 km  
(6,250 mile)  
Indicates the mode currently selected.  
Tm (Tm 2) ............... [Elapsed Time]  
Dst (Dst 2) ............... [Trip Distance]  
Av (Av 2) .................. [Average Speed]  
Mx ............................ [Maximum Speed]  
Odo .......................... [Total Distance]  
............................ [Clock]  
*This is the average figure of being used under 20°C temperature and  
the dis tance between the computer and the sensor is 65 cm.  
* If the backlight is used frequently, the battery life diminishes accordingly.  
Controller .......................... 4-bit 1-chip microcomputer  
(crystal controlled oscillator)  
#169-9760  
Display ............................... Liquid crystal display  
Sensor ............................... No contact magnetic sensor  
Wheel Circumference Range ....... 0100 mm - 3999 mm  
(default figure A : 2095 mm, B : 2050 mm)  
Working Temperature ....... 0°C - 40°C (32°F - 104°F)  
Dimension/Weight  
Magnet for Composite Wheel  
H
I
J
Wheel size icon  
Backlight button  
Battery Case Cover  
52.5 x 38 x 22 mm [2-3/32" x 1-1/2" x 7/8"]  
/ 30 g [1.06 oz]  
Starting/Stopping measurement  
This computer allows automatic (Auto-mode) or manual measurement.  
During measurement, the speed unit icon flashes. The maximum  
speed and total distance will update, regardless of measurement.  
• Auto-mode (automatic measurement)  
* The factory-loaded battery life might be shorter than the above-men-  
tioned specification.  
* The specifications and design are subject to change without notice.  
#169-9690  
Hi-Power Wheel Magnet  
If the  
icon is visible, measurement is automatic.  
In Auto-mode, starting/stopping measurement using the START/  
STOP button is impossible.  
• Manual measurement  
If the  
icon does not light, starting/stopping the measure-  
ment using the START/STOP button is possible.  
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two  
conditions: (1) This device may not cause harmful interference, and (2) this device must  
accept any interference received, including interference that may cause undesired operation.  
Modifications The FCC requires the user to be notified that any changes or modifications  
made to this device that are not expressly approved by CatEye Co., Ltd. May void the users  
authority to operate the equipment.  
* Use the menu screen to toggle between Auto-mode ON and  
OFF. For further information, see the MENU FLOW.  
Switching Mode symbol ....................................  
b
Press the MODE button to switch measurement according to the  
OPERATION FLOW.  
Press the MODE button for 2 seconds to switch from Main to Sub  
measurement.  
LIMITED WARRANTY - 2-Year Computer/Sensor only  
(Accessories/Attachments and Battery Consumption excluded)  
• Sub measurement  
If trouble occurs during normal use, the part of the Main Unit or sensor will be repaired or  
replaced free of charge. The service must be performed by CatEye Co., Ltd. To return the prod-  
uct, pack it carefully and remember to enclose the warranty certificate with instruction for repair.  
Please write or type your name and address clearly on the warranty certificate. Insurance, han-  
dling and transportation charges to our service shall be borne by person desiring service.  
When Main measurement starts/stops, Sub measurement starts/  
stops accordingly. Note, however, that the main and sub mea-  
surements must be reset individually.  
Resetting Main and Sub measurement at different times allows  
interval measurement to be carried out.  
* In the sub measurement the pace arrow compares the current  
speed to average speed 2.  
Service & Research Address for USA  
CO.,LTD.  
2-8-25, Kuwazu, Higashi Sumiyoshi-  
CATEYE Service and Research Center  
c
d
Resetting data ........................... Main :  
Sub :  
1705 14th St. 115 Boulder, CO 80302  
To reset measurement data, display the Main/Sub measurement  
data and press the START/STOP and MODE buttons simulta-  
neously. Trip distance is not reset.  
ku, Osaka 546-0041 Japan  
Phone: 303.443.4595  
Attn: CATEYE Customer Service Section  
Toll Free: 800.5CATEYE  
Fax: 303.473.0006  
Backlight  
Press the backlight button to illuminate the display for 3 seconds.  
If the battery is low, the wheel size icon flashes and the display  
does not illuminate.  
Power-saving function  
If the computer has not received a signal for 10 minutes, power-  
saving mode will activate and only the clock will be displayed. When  
the computer receives a sensor signal again, the measuring screen  
reappears. If two weeksinactivity elapses, power-saving mode will  
change to SLEEP mode. Pressing the MODE or START/STOP but-  
ton in SLEEP mode brings up the measuring screen.  
Dual Wheel Size  
Two wheel sizes (Wheel sizes  
and  
) can be registered on  
the computer. This is useful when the computer is shared be-  
tween two bicycles or when one bicycle uses different wheel sizes  
at different times. Wheel size B has pre-programmed for a 26x1.95"  
size tire.  
* Use the menu screen to toggle between  
ther information, see the MENU FLOW.  
and  
. For fur-  
Changing the computer settings  
If the MENU button is pressed with the measuring screen dis-  
played, the menu screen appears. Press the START/STOP button  
when measurement has stopped and no signal is being received  
to change menu settings.  
• Setting the clock  
Set the clock via  
Settings in the MENU FLOW.  
* For the Speed unit, reset Main and Sub measurement data  
before changing settings.  
* For further information, see the MENU FLOW.  
Maintenance  
To clean the computer or accessories, use diluted neutral deter-  
gent on a soft cloth, and then wipe it off with a dry cloth.  
3
 

Belkin Power Supply F6C110 RKM 2U User Manual
BenQ Computer Monitor T2210HD User Manual
Black Box Modem MICRODRIVER 9 User Manual
Blomberg Refrigerator KGM 9690 User Manual
Brother Label Maker PT 7100 User Manual
Campbell Hausfeld Sander CL156700AV User Manual
Carrier Portable Generator ASPB07 1SI User Manual
Casio Electronic Keyboard AP 420 User Manual
Cecilware Kitchen Grill ELG 1F User Manual
Cecilware Refrigerator 08725 User Manual